Part no. AH-LB1-011
1915cc LONG BLOCK - With TURN KEY option.ALL NEW PARTS Stock or Performance
No exhaust or clutch included
AUTOLINEA CRANKCASE – Mag case (Super Race case for Cranks bigger than 82mm or available as upgrade)
*** CAMSHAFT KIT - Engle or Scat with Aluminium helical gear (Steel Straight Cut Upgrade)
- 1915cc LONG BLOCK - ALL NEW PARTS BUILD 2021 (With option to make turn key engine)
- ALL BRAND-NEW PARTS
- Not a refurbished part in sight & no exchange required!
- KEY COMPONENTS
- Items with *** have options available
- STOCK BUILD
- Full flowed case/pump with remote twist on filter (except for 1600/1641cc)
- HEAD STUD KIT - 8mm chromoly with heavy duty nuts/washers
Full specification
Stock or Mild Performance Camshaft Choice: (Give your vehicle that extra boost. Effectively moving the rev range higher to gain more HP)
Single Carb and manifold. New tinware, Alternator Kit with Stand, Fan kit, Mechanical Fuel Pump, Codan R9 Fuel Lines, New Distributor/Leads/Coil, Plugs
Twin 34 Carbs and manifold. New tinware, Alternator Kit with Stand, Fan kit, Mechanical Fuel Pump, Codan R9 Fuel Lines, New Distributor/Leads/Coil, Plugs
All engines are priced without an exhaust or heat exchanges. This is due to the varying styles available for various vehicles.
- FORGED CRANKSHAFT – Counterweighted 8 Dowels Dynamically Balanced with Flywheel
- FLYWHEEL – 200mm 12 volt, Lightened 8 Dowel cast
- GLAND NUT - 38mm Heavy duty Chromoly/Washer (36mm on 1600/1641cc)
- *** CON RODS - Chromoly I-beam 5.4” VW Journal (H-beam upgrade)
- CAM FOLLOWERS – Matched to camshaft
- MAIN BEARING SET – Standard size
- ROD BEARING SET - Standard size
- CAM BEARING SET - Standard size Double Thrust (Single on 1600/1641cc)
- ***OIL PUMP - 26mm (30mm Pump with Oil Cooler Kits fitted)
- OIL PUMP COVER – Full flow cover (Stock Steel type available on 1600/1641cc)
- DEEP SUMP – 1.5qrt
- ***OIL DRAIN PLATE – Stock Steel type (Billet Aluminium upgrade)
- ***PISTONS & BARREL KIT - Cast (Forged upgrade)
- ***PUSH-ROD TUBES – Stock Steel or Racing wide end (Aluminium sprung type upgrade)
- ***CYLINDER HEADS - Stock or Big valves
- PUSH-ROD SET - Chromoly Steel
- ROCKER SET - Bolt up shaft type (Forged 1.25 Ratio upgrade)
- ROCKER COVERS - Aluminium Bolt On or stainless-steel clip on
- GASKETS - Best quality Elring kit
- OIL RELIEF KIT – Stock type
- Options List:
- (Everything below can be selected on the options panel)
- NEW Cylinder Heads:
- Twin Port Heads: (Autolinea, Classic line, Empi)
- Stock Camshaft
- Engle W-100 (or Scat c25)
- Engle W-110 (or Scat c35)
- Pushrod Tubes:
- Steel
- Stainless Steel
- Rocker Covers:
- Stock
- Bolt up Aluminium
- Rockers: (required for cams W-110 above)
- Bolt up Rocker shaft
- Crank Case:
- Used for Beetle
- Used for Early bay and later
- NEW MAG AS41
- Flywheel:
- 180mm USED ONLY
- 200mm 4 dowel Full Weight
- 200mm 8 dowel Lightweight
- Full Flow Options:
- None
- Full flow case/Cover (Without engine bars)
- Full Flow In/Out Cover (Vehicles with engine bars)
- Looking for a TURN KEY based on a refurbished engine, Ready to bolt into your vehicle!
- Turn Key options
- SINGLE CARB:
- Crankshaft & Alternator Pulley (Steel)
- TWIN CARB: